Z Car Garage is proud to offer a CV axle conversion kit for your Datsun S30 and 510. We have sold over 100 sets of axles globally, with customers installing and enjoying them on everything from street cars to full-blown IMSA racers. These CV axles will help transmit power to the ground and ensure smoother operation compared to your standard half shafts. Full details below:

 

For years we have used aftermarket CV axles that utilize an aluminum adapter prone to loosening up over time. Despite efforts to keep things tight (Loctite, hardware changes) we had to keep an eye on them. We developed a better solution that eliminates the need for aluminum adapters and remains 100% bolt-in like a factory half-shaft.

  

Designed and manufactured locally with KAD Models, the ZCG CV axle kit works in both R180 and R200 configurations.

 

  

These are the beefiest CV axles on the market. They have been tested on the track by our vintage racing customers and also in high hp* street cars (powershifting, clutch dumps, etc.). Each axle has a serial # for peace of mind:

 

The CV axle kit is available now from ZCG for 1595.00 + freight and they come with everything you need to install on your car. Contact us at 408-452-0350 or send Rob an e-mail rob@zcargarage.com to purchase. Installation is just like doing a half-shaft: there is even a marking that shows you where to line up bolts and special hardware:

 

The ZCG CV Axles in action

The video below demonstrates the “looseness” associated with aftermarket CV axles that use adapters compared to the ZCG axles without adapters. Several customer race/street cars running our CV axles are also shown. Enjoy!

 

S30 and 510s running the ZCG CV axles

 

Randy Jaffe’s #46 BRE Datsun 240z received the very first set of ZCG CV axles: Serial # S30-000240!

 

The Bluebird SSS Coupe and Hakosuka Skyline are both running ZCG CV axles on the race track:

   

Race car driver and restoration specialist Jim Froula of Racecraft is running ZCG axles in several of his cars:

Set #246 – installed May 2018 on the “Harry Stewart #52” Datsun 510:

  

Set #247 – installed April 2018 on the 260z

  

Set #248 – will be installed on Adam Carolla’s “Greg Sorrentino #90” Datsun 510. We are pleased to report that Jim will also be installing a set on his “George Alderman #32” 300ZX! The ZCG CV axles are also perfect for high hp street cars. The following customer cars are all running our CV axles now:

Frank B’s fuel-injected, 6-speed stroker L-series:

  

Gary’s 430whp LS3-powered 280z:

  

Scott W’s EFI stroker L-series:

  

James S’ L28ET:

  

Brian’s 1972 240z:

  

Finally, Gary’s “Behemoth”  OS Giken TC24B1Z powered S30:

Technical Information:

The Z Car Garage axles were designed to help remove much of the backlash aka clunk seen in many older vehicles. Modern technology has given us the ability to create a set of axles to exacting standards. We started with a high quality set of CV joints that were found to be the most consistent in both major and minor spline diameters. We then began to design the axle itself to share the same tight tolerances. We are holding a +/- .01mm diametric tolerance on both the inner and outer spline diameters. This gives us the feeling of direct connection between differential and wheel. The axle shaft major diameter was increased to 30MM to give owners a bit of added comfort in knowing the main shafts are stout. Once the axles are splined they are then heat treated to obtain the desired harness. After heat treat the axles are then nickel plated to add corrosion resistance. The inner and outer flanges are made from 316 stainless steel and mate to the CV joints with tapered alignment surfaces to ensure concentricity is maintained throughout the axle thus reducing vibration. The inner flange attaches to the stock R series differential utilizing the Nissan factory hardware. The outer flange attaches to the driven stub with bolts specifically designed and manufactured for the Z Car Garage axle installation kit. These bolts are manufactured to grade 12.9. All ZCG axles are manufactured locally which helps us maintain the fitment and quality we require.

Materials

Axles : Hardened AISI/SAE 4340 Alloy Steel, 4340 is a nickel-chromium-molybdenum alloy steel

Drive flanges: 316 stainless steel, Type 316 steel is an austenitic chromium-nickel stainless steel

Outer Flange Bolts: Hardened 4140 Alloy Steel , AISI or SAE 4130 grade is a low-alloy steel containing chromium and molybdenum as strengthening agents

 

  

“Love cars. Love people. Love life”…this motto was immortalized by Nissan legend Mr. K, and embodied perfectly by car enthusiast Ben Y with his 1974 Datsun 260z. We met Ben in Fall of 2016 when he visited Z Car Garage for a full mechanical restoration and it’s been a joy helping him realize his sportscar dream. Read on to learn about the Z’s history and how our restoration efforts culminate with a memorable father-son roadtrip.

 

A Family Affair

Ben has owned this S30 for nearly eighteen years. The car really is a family affair beginning with his father:

 

“I was showing it a lot as a college student and won best stock 260Z at the MSA nationals in 2002. The picture below (left) of me and my dad with Matsui-San was a great time in my Z life. I was learning so much and he was and still is one of my hero’s. The car he is pictured in is Katsuaro-San’s (Kats) 1970 240z. On the right,  I mounted a free set of stock steelies/hubcaps because I thought the factory fresh look was what I was going for. I waited until I found the right set of Watanabe’s.”

 

“In 2005 I took my 260Z to a show in Fremont at Ohlone college where I saw Rob with his green 240z complete with red Porsche brakes, RB25, and the photo of his “Z” tooth.  His car was unforgettable and with me pursuing a career in dentistry I would never forget his tooth.”

 

Ben has written a blog dedicated to his Datsun addiction HERE. His ultimate goal with the 260z is to complete a coast-to-coast trek of the United States for the 50th anniversary of the Z car in 2020 with his family.

Let’s move on to the restoration…

Building the Dream

  

Ben’s vision of his perfect Z car comes from his admiration of period-style Japanese tuning:

“My concept is to create a 260Z as if it was owned in the 1970’s in Japan by someone who worked at the Datsun Sports Corner. When looking at the car’s engine-bay, interior, and exterior it is neither original nor modified.  I am open to making modifications to improve the car’s drivability, but outside of the Datsun Competition parts the changes will need to be internal.”

We performed a full inspection on the Z and it had a long list of needs. Ben reported the car lacked power and we found cylinders ‘3’ and ‘5’ in bad shape, necessitating a rebuild. The engine was removed while a 3.0L Rebello was built.

 

We wanted to build the car exactly to his specification and Ben decided to not leave a single rock unturned with engine, cooling system, exhaust, suspension and braking refurbishment. We would also install his prized Datsun Competition racing seat.

Engine Bay

With the tired engine removed we began the clean-up process.  Many more pictures of the teardown and assembly in the gallery:

  

All new hydraulic lines replaced corroded parts:

  

In keeping with Ben’s desire to have a factory-looking appearance, the new 3.0L engine retained SU carbs, built by Z Therapy. A JWT Aluminum flywheel and HD clutch back the powerplant:

    

Ben’s excellent choice of exhaust: the Fujitsubo Legalis R twin-pipe system:

 

From header to twin tail-pipe we love the craftsmanship, finish, sound and performance this setup offers.

  

We added our own touches like a factory-like silver finish at the rear and O2 bungs for Wideband tuning in-house:

   

Small details in the engine bay make a huge difference:  powdercoated air filter assembly with reproduced OEM decals throughout,  proper plating, wire clips for hoses, ZCG mods to intake/exhaust manifolds and a stock radiator updated to 4-core:

 

The completed engine bay:

 

Chassis

As the engine bay started to come together we realized the chassis needed to match the rest of the car. The drivers’s side inner fender had enough rust to compromise the sway bar mount. We cut it out, built a new brace for the sway bar mount and welded in a replacement panel.  All inner fenders were cleaned/undercoated.

 

The entire fuel system was gone through including all recovery hoses/lines, fuel sender and boiling out the gas tank:

  

The Z received entire front and rear suspension refurbishment with full coil-over suspension from Techno Toy Tuning. New parts included adjustable T/C rods, rear control arms, new bushings, rack bushings, steering coupler, ball joints and more. All parts were powdercoated:

 

Steering rack before/after and the T3 suspension going in. All nuts/bolts were bagged for zinc plating:

   

T3 f/r coil-overs and Suspension Techniques f/r sway bars:

  

The braking system was restored to factory spec to keep it vintage. Mild performance upgrades included Stoptech 309 pads with slotted front rotors and stainless steel braided brake lines.  All wheel bearings were replaced. Up front we replaced the front calipers with NOS units:

 

In the rear, stock suspension and old brakes vs new:

  

The drums were turned and new Nissan wheel cylinders/shoes installed:

   

The T3 coil-overs allow ride-height adjustment and Ben’s Z now sits much lower over those gorgeous Watanabe wheels with generous sidewalls:

“One of my hero’s had Watanabe’s on his car and that sealed the deal in terms of me eventually deciding on a wheelset.  My set’s dimensions are 14″ x 7.5jj (+1.5mm) for the rear and 14” x 7jj(+8mm) for the front, Type B. “

Stock suspension vs T3, more pics gallery!

 

We love it:

 

Datsun Competition

Ben’s appreciation for Datsun’s Competition-specific parts can be highlighted in the interior where he has an original rallye shift knob, steering wheel and for the tifecta: the competition seat. He even tracked down the matching headrest from a Bluebird.

   

He’s super passionate about the Comp seat, you can read more about it in his personal blog post HERE. We removed the factory seat, made a bracket to allow his comp seat to fit and installed it. It looks great with that un-cracked factory dash!

  

We paid attention to all of the little things that make a Z car fun to drive everyday. Finalizing door fitment and getting the vintage A/C unit working again was important:

“I want to drive it across the country. That is a big goal of mine, but really I just want to drive the car always.”

Since A/C had been on Ben’s mind, we fixed and made one of the lines, all mocked up to clear the Fujitsubo header. More details in the engine bay to satisfy’s Ben’s penchant for the vintage look: we passed along our rare factory spark plug wires and OEM choke cable set.

 

  

Enjoying The Ride

With the mechanical restoration completed, Ben embarked on his originally planned road trip with his father.

“I got back last night from my trip with my Dad. We went a bit north of 1000 miles in three days in my Z Car Garage 260Z! The car is perfect. I really want to thank you for building such a glorious machine. It does everything it should. Handles well, makes all the right sounds, is comfortable, and soaks up the miles. I took it up to an elevation of 7500′ without even a hiccup. My Dad drove a lot and he loved it too. He got it up to 100mph on the highway and I didn’t even know it the car was so smooth. He told me later.”

 

 

We were stoked for Ben. Seeing him drive the Z everywhere, including a visit to the epic 2018 RMMR where Datsun was the featured marque. Being on the road is really what he loves and the S30 is a scalpel.

 

Love for the Z, with Family

Ben’s family is an integral part of his Z passion. He even had these T-shirts made for his crew. Rob has one as well 🙂

 

George S returned to ZCG for a few items on his 57k-mile survivor S30. Here is a brief history on the Z:

George owned a 1971 Datsun 240z back in 80’s, sold it in the 90’s and recently tracked the car down to its current owner in Atlanta. Sadly, after all those years the Z wasn’t in the greatest shape (2013):

 

I purchased it in August 1981 with 75,000 miles from a single girl in the Marina District. It was my every day car for 10 years, putting on an additional 75k miles. Along the way added the Enkei gold rims, added a Monza exhaust system which was popular then and re-painted it in 1990(similar shade, but not the Datsun blue)

Serviced it regularly and never had to do anything other than the basics. She ran like a charm, was never in an accident.

Sold it in 1991 to a guy I worked with who drove it back to Tennessee a short while later. Thought about the car often, but had no info on it until the guy in Atlanta called me in October 2013. Think he said the car had about 190k miles.

George, obviously missing his Z car after tracking it down had considered restoring it and consulted with us at ZCG. It turns out that Rob actually knew the current owner in Atlanta and the two discussed the Z’s state of repair. Rob felt that it was one of those cars that would be difficult to stay ahead of the curve on. The recommendation: buy an S30 that’s ready to drive, and that’s exactly what George did…

 

In 2016 George picked up a 1972 240z with an automatic transmission in SoCal. We were impressed with its super low 57k miles, original paint and stunning red interior.

   

Once it arrived at ZCG we went on and corrected issues with braking system and fixed front suspension parts. We found a really clean set of Series 2 wheel covers to replace the later units and really made the car standout proper.

 

George recently came in for more sorting, paint correction and passenger mirror replacement. In the engine bay, a Pertronix ignition was installed and timing set to ensure the car ran perfectly.

  

Moving to that gorgeous red interior, the shift handle was replaced:

 

The exterior was treated to some dent removal and paint matching on body panels. The previous owner installed a black aftermarket passenger mirror:

 

We removed the black part and installed our favorite mirror:

    

This Z is a great example of how a stock car can be updated and maintained to bring many smiles per gallon. Enjoy The Ride, George!

 

 

Z Car Garage is expanding to support our vintage, late model and motorsport work. We are seeking an experienced and skilled automotive technician to join our team.
This is not an average automotive job. The position is for a special candidate that wants to be part of a shop that is growing and always striving to set the bar a little higher. We offer competitive pay/benefits and the best working environment.
Requirements: Experienced with a good set of tools, willingness to learn, and be part of a team.

Interested or know someone who might be a good fit? Please contact rob@zcargarage.com or call us at (408)452-0350.

 

 

 

***HAPPY HOLIDAYS From Z Car Garage***

 

One of the real joys this holiday season is the opportunity to say thank you and wish you the very best for the new year. From all of us at Z Car Garage we thank our friends, family and customers again for another exciting and productive year! Please note our holiday closure below:

 

ZCG will be closed from 12/21 to New Year’s Day. We will re-open for business on  1/2/19

 

 

Before we take a look back at highlights from 2018, check out a few of the many customer projects coming along at the shop including full restorations

Scott W’s 260z was completed in summer. This Z has a complete color change, ZCG Big-Brakes and a sweet 3.2L with Jenvey ITB fuel injection. Full report in the New Year!

 

Several cars delivered before the holidays will get full reports soon: Cece’s 1977 Datsun 280z, Patrick’sZ32TT and Jay’s Z32TT

  

 

Highlights from 2018

Enjoy these highlights from 2018 and  Z you in the New Year!

The Bring a Trailer Datsun 240z

Jalopnik Visits Z Car Garage to Talk Nissans

ZCG Goes to SEMA

Great Drives: Mt.Umunhum to Alice’s

James’ Turbo 240z on Speedhunters

Japanese Classic Car Show

The Rolex Monterey Motorsports Reunion

The ZONC Nissan Show

The Mitty

Courtney’s Datsun 240z

Thanks to Nick L for reminding us of this awesome Nissan commercial, Enjoy The Ride!