We love to see owners installing our Z Car Garage CV Axles on their vintage Nissans and Datsuns. Ray H added a set to his 1971 Skyline that he acquired from our friends at JDM Legends. Ray also visited Z Car Garage for dyno tuning and alignment services which transformed this Hakosuka.

  

Ray has been a ZCG client for many years. We first saw his Skyline at the 2019 Golden Week Kyusha Festival where I spoke to him about visiting ZCG for some upgrades and tuning.

 

Fast forward to 2021 and I spotted Ray at the Driving While Awesome gathering. He pleasantly informed me that he was running our ZCG CV Axles (serial # 00356) and we are happy to report that he installed them himself!

“I have been wanting to go with CV’s for a while on my SR 510. I have been following a few suppliers since they first started showing up about 10 years ago. I did notice that people were having problems with them wearing out and also that there were a few redesigns. On my Hako, I desperately needed to a wheel bearing and half shaft u-joint replacement as it was making some awful clunking noises back there. So, when I started seeing your blogs about the CV’s I was immediately interested. Knowing Rob, I knew these had to be good!”

 

Ray sent us a few installation pictures of the ZCG CV Axles replacing the old CVs and the R180 STI LSD:

“It was just an optimum time to get these when I had my entire rear suspension out for a rebuild and upgrade. The installation was pretty straightforward.” So far all good, I don’t think my modest power has put these to the test but its nice to know something has been well engineered and its one thing I wont have to worry about, not mention they look bitchin!”

 

For more information on our Z Car Garage CV Axles please read below. Before we share the dyno tuning results, let’s take a look at how Ray found his Skyline…

Datsuns From the Beginning

 

It is worth noting that Ray is a die-hard Datsun (510) enthusiast with ties to the old Nor-cal 510 club from decades ago. In the groovy group photo above, Ray is in the back row, last 510 on the right! Here it is, his first Datsun 510 circa 1981 (below, left) and same car with flares and a Cartech turbo kit in the FAR Performance parking lot!

 

Ray shares the story of his Skyline:

“I have always loved the 510, my first car in high school and still own 3 currently. When the internet started to become a regular thing I noticed these awesome looking boxy cars by Nissan sold only over there and I think Europe. I eventually stumbled upon JDM Legends website about 10 years ago and started inquiring about how much they cost and how to get one. Erik at a couple different times offered me a chance to buy one, however timing was just not right for me at the time. Fast forward a few years and Velocity channel (now Motortrend) starts promoting a show with Hakos running around! I instantly got the bug again and thought “these things are going to explode in value, If I don’t get one now I never will”.

Much to my amazement, I got a call within a month. He said “I got a line on a couple in Japan, one sounds exactly what you looking for”. He sent me pictures and I think I agreed to buy it the next day, still remember July 4th, 2018! Took about 3-4 months to get to Long Beach, then immediately to Utah. Once it was in Utah, Erik and Josh went through the whole car so it was a ready to go.”

“I flew out to Utah after he had it for a month to go over additional upgrades. First off, he said this was one of the cleanest, most solid chassis he’d ever brought over! It really goes to show, you get what you pay for. I cant stress enough, pay the money up front, it is so worth it to get a solid car with everything on it! The additional work they performed included, flaring the front and ordering wider Watanabes, modern fuse block conversion, new spoiler upfront, Mauricio did the paint match! I picked up in November of that year and trailered it all the way home.”

 

Since picking it up from JDM-L, Ray has been driving the Hako frequently. Quick specs:

1971 Nissan 2000 GTX , finished in white as GTR tribute

Engine:
2.8 L series straight six, Late 5 spd transmission, N42 head, Triple Italian Weber 40’s, Headers with Fujitsubo exhast, All original mechanical linkage.

Suspension:
Watanabe 15×9.5 -26 rear 15×8.5 -6 front, Toyo RA1 225/50/15 rear 205/50/15 front, Modified rear crossmember with FotoFab camber/toe brackets (510), QA1 double adj.rear shocks, ZCG CV’s, Subie R180 3.9 LSD, Finned aluminum rear drums, New Nissan bushings, bearings, driveshaft U-joints, brake cylinders, T3 280ZX front strut with coilover and aluminum hubs and Koni yellow adj. struts.

 

Exterior:
Protec over flares and front spoiler
GTR front grill and badging
Complete chrome trim and new weather strip

Interior:
Power windows, GTR shift knob and emblem, Stock Seats, Nardi steering wheel, Coco mats, Stock radio. All functioning and complete switches and dash.

 

Ray also has several 510s including a ’72 510 2dr (S15 SR20DET) “SaRafina”, ‘72 510 4dr “Mossy” and ‘69 510 2dr “project Scotty”. Follow Ray and his Datsun adventures on Instagram.

Dyno Tuning

 

Ray was experiencing some driveability issues and considered changing his triple-Weber induction to triple-Mikuni to resolve it. We suggested bringing it in for Rob to diagnose, tune and also provide alignment services. Before hitting the dyno, Rob and Josh identified the major culprit-the throttle linkage was not allowing wide-open operation.

 

The throttle-linkage was fixed and Rob was able to dyno tune the L28 with the triple-Webers for best AFR/timing. The results were astounding: baseline was 53hp/83tq and after tuning 162hp/169tq to the wheels!

 

It’s not unusual to pick up 10-15whp with Rob’s dyno tuning of your vintage car, but Ray gained a whopping 109hp/86tq. After driving the Hako after ZCG tuning/alignment he was ecstatic:

“My experience at ZCG and the dyno – Freakin awesome! Way exceeded my expectations! I’ve already had many people ask me “can he get me in there, I need that”. It’s actually kind of a bummer, that he is so booked up, I’m sure there are many people that would love to get there car in there and unlock some potential! My Hako is so much more driveable now, tracks straight with the alignment and the power gain, amazing! Like I told you, my Solex 44’s are ready, but I just want to enjoy this now for a while.”

 

Enjoy this video we made of the Skyline in action: dyno passes, in-car testing with Rob and Ray’s first drive/reactions. Volume up!

 

Evening shots with Ray in amazement after his test drive…

 

 

Alignment Services

 

Z Car Garage offers full alignment services for your late model and vintage car. Ray’s Hako was fully-aligned by our lead technician Josh who has many hours of street and race car setup experience. Caster was optimized here for better steering/stability.

 

 

 

Enjoying The Ride

 

We were super stoked to see Ray so happy with the Hako and he continues to drive and enjoy it.

“As I get up here in age, it is very important that my collector cars run! I’m no longer interested in endless project cars. Now I just want to get out there and drive! This leads into my praise for JDM Legends, like ZCG they just get it. Erik Bizek, like Rob, has a crazy passion for these vintage cars which I love.”

Thank you for your support Ray, and for letting us be a part of your Hakosuka. We look forward to working with you again and seeing you on the road!

 

 

We have many more photos in the gallery and please read below for more information on our ZCG CV Axles:

ZCG CV Axles

Our Z Car Garage CV Axles help transmit power to the ground and ensure smoother operation compared to your standard half shafts. These are 100% bolt-in replacing your half-shafts and does not use aluminum adapters commonly found in aftermarket units. We have over 200+ CV axle kits on customer cars and we are stoked with all of the positive feedback.

   

For years we have used aftermarket CV axles that utilize an aluminum adapter prone to loosening up over time. Despite efforts to keep things tight (Loctite, hardware changes) we had to keep an eye on them. We developed a better solution that eliminates the need for aluminum adapters and remains 100% bolt-in like a factory half-shaft.

  

Designed and manufactured locally with KAD Models, the ZCG CV axle kit works in both R180 and R200 configurations.

  

These are the beefiest CV axles on the market. They have been tested on the track by our vintage racing customers and also in high hp* street cars (powershifting, clutch dumps, etc.). Each axle has a serial # for peace of mind:

 

The CV axle kit is available now from ZCG for 1595.00 + freight and they come with everything you need to install on your car. Contact us at 408-452-0350 or send Rob an e-mail rob@zcargarage.com to purchase. Installation is just like doing a half-shaft: there is even a marking that shows you where to line up bolts and special hardware:

 

The ZCG CV Axles in action

The video below demonstrates the “looseness” associated with aftermarket CV axles that use adapters compared to the ZCG axles without adapters. Several customer race/street cars running our CV axles are also shown. Enjoy!

 

Enjoy this video made by our client Hazel. She installed our ZCG CV Axles on her Hazel’s 1970 Datsun 240Z

 

Over 150 sets of our ZCG CV Axles are installed in client’s cars all over the world:

Supermachine in Tokyo, Japan is running our Z Car Garage Big-Brakes and Z Car Garage CV Axles in their Series Datsun 240Z:

  

Race car driver, restorer and Datsun Historian Glenn Chiou is running our ZCG CV Axles in this IMSA GTU 260z race car!

  

Racer Brad H is running ZCG CV Axles in his IMSA GTU race car:

  

Race car driver and restoration specialist Jim Froula of Racecraft is running ZCG axles in several of his cars:

Set #246 – installed May 2018 on the “Harry Stewart #52” Datsun 510:

  

Set #247 – installed April 2018 on the 260z

  

Set #248 – installed on Adam Carolla’s “Greg Sorrentino #90” Datsun 510.

  …[read more]

 

We love to see owners installing our Z Car Garage CV Axles on their vintage Nissans and Datsuns. Julio added this 1972 Skyline to his collection and had the team at KaiserKars replace the old CVs with our ZCG CV Axles. You may have seen the Hakosuka at at events in the SoCal area and we are proud to be part of it!

 

We met Julio last year at the Japanese Classic Car Show where his Skyline was on display in the Hagerty booth. He pleasantly informed us that he was running ZCG CV Axles and we are happy to report that the team at KaiserKars installed them with ease at their facility in Los Alamitos, Ca:

“Our in-house technician said the installation process was very straightforward and simple, basically just a bolt on/bolt off slid right in and bolted each axle to the differential and it was finished. It went as smooth as it could go.”

 

The team at KaiserKars sent us a few installation pictures of the ZCG CV Axles replacing the old CVs. They shared their experience:

“We were recommended the upgraded CV Axles by a friend of ours that pointed us to Rob. The Skyline came with some rear differential knocking/popping issues, the upgrade fixed the problem. We eventually got in contact with Rob himself and he asked us a few things in regards to what was currently on the car. We think they were a kit by the previous owner but they were completely shot and beyond rebuilding.”

  

Skyline Dreams

 

The Hakosuka Skyline is undeniably a JDM icon. We asked Julio about his history with Japanese classics:

“I have been a car geek all my life, but as all guys my age, Fast and Furious, Gone in 60 Seconds, Motorweek and the Saturday/Sunday cable shows were the culprits for my love of all cars. But once I watched Hot Version/Option, and Initial D anime I was smitten by JDM cars and culture, I longed to ride in a GTR, drift an AE86 and own all the unicorn cars I grew to idolize. So far the hunt is on and I seem to be collecting them like others collect Hotwheels. The Hakosuka has been a love affair for me as I regret selling my last one in a bad deal but this one makes up for that bad memory and I could not be happier with its stance, power and aura.”

The Hako features some of our favorite parts like the Rebello 3.2L with Jenvey ITB induction:

 

In addition to the upgraded ZCG CV Axles the Hako also has an R200 LSD diff, 5-speed transmission, 16″ Watanabe R-Type wheels (8.5/9.5), Rubber Soul stainless exhaust system and T3 suspension. Outside, the body is VW Limestone Grey Metallic with carbon fiber flares, GT-Kai badging and re-finished bumpers in eggshell black. More pictures in the gallery below!

 

Thank you for your support Julio, it was great meeting you at JCCS! Also, thank you to KaiserKars we look forward to working with you! Please read below for more information on our ZCG CV Axles:

ZCG CV Axles

Our Z Car Garage CV Axles help transmit power to the ground and ensure smoother operation compared to your standard half shafts. These are 100% bolt-in replacing your half-shafts and does not use aluminum adapters commonly found in aftermarket units. We have over 150+ CV axle kits on customer cars and we are stoked with all of the positive feedback.

   

For years we have used aftermarket CV axles that utilize an aluminum adapter prone to loosening up over time. Despite efforts to keep things tight (Loctite, hardware changes) we had to keep an eye on them. We developed a better solution that eliminates the need for aluminum adapters and remains 100% bolt-in like a factory half-shaft.

  

Designed and manufactured locally with KAD Models, the ZCG CV axle kit works in both R180 and R200 configurations.

  

These are the beefiest CV axles on the market. They have been tested on the track by our vintage racing customers and also in high hp* street cars (powershifting, clutch dumps, etc.). Each axle has a serial # for peace of mind:

 

The CV axle kit is available now from ZCG for 1595.00 + freight and they come with everything you need to install on your car. Contact us at 408-452-0350 or send Rob an e-mail rob@zcargarage.com to purchase. Installation is just like doing a half-shaft: there is even a marking that shows you where to line up bolts and special hardware:

 

The ZCG CV Axles in action

The video below demonstrates the “looseness” associated with aftermarket CV axles that use adapters compared to the ZCG axles without adapters. Several customer race/street cars running our CV axles are also shown. Enjoy!

 

Enjoy this video made by our client Hazel. She installed our ZCG CV Axles on her Hazel’s 1970 Datsun 240Z

 

Over 150 sets of our ZCG CV Axles are installed in client’s cars all over the world:

Supermachine in Tokyo, Japan is running our Z Car Garage Big-Brakes and Z Car Garage CV Axles in their Series Datsun 240Z:

 

Race car driver, restorer and Datsun Historian Glenn Chiou is running our ZCG CV Axles in this IMSA GTU 260z race car!

  

Racer Brad H is running ZCG CV Axles in his IMSA GTU race car:

  

Race car driver and restoration specialist Jim Froula of Racecraft is running ZCG axles in several of his cars:

Set #246 – installed May 2018 on the “Harry Stewart #52” Datsun 510:

  

Set #247 – installed April 2018 on the 260z

  

Set #248 – installed on Adam Carolla’s “Greg Sorrentino #90” Datsun 510.

  …[read more]

 

Pall K acquired this Pearl Red (AH3) R32 from our friend Sean and his team at Toprank International Vehicle Importers. It goes without saying, if you are in the market for a vintage Skyline (or any JDM car) IVI is the place to go. We love the gorgeous paint color and Volk TE37SLs:

 

Pall brought the R32 to ZCG for a full inspection in 2019 and we have serviced it since. On that visit we found one of the CV boots torn and he had some Nismo stainless lines for us to install. We checked the timing, changed the engine oil, transmission fluid, installed the new brake lines front/rear and performed a full alignment. He visited us again for a new clutch:

  

Pall has driven the Skyline frequently since we met in 2019, and he does most of the work on his cars himself. We spotted him last summer at the 6/13 Morning Motors Cars & Coffee event hosted by DrivingWhileAwesome (DWA) in Santa Cruz, CA:

 
I had fun chasing Pall in our shop Datsun 240Z (Mrs. Butters) on this earlier 2020 Drive:

  

Pall was experiencing some intermittent issues with car, so he purchased a Haltech Platinum Pro ECU from our client Kurt W since he’s going to an Haltech Elite box for his own R32 GT-R build.

“My car was pinging on 91 octane trying to run on the stock ECU at higher load / RPM. I purchased a Haltech Planimum Pro plug-in ECU to resolve the pinging issue and make the most of my modifications. Rob installed the Haltech with a wideband O2 controller and dyno tuned the whole setup. The pinging issue is gone and the car feels incredible. Smoother initial throttle tip-in and lower end, pulls hard all the way out redline. Extremely pleased!”

 

As Pall mentioned above, his R32 came in to Z Car Garage in Novemeber and Rob dyno tuned it using Haltech. It put down a very strong 381hp/320tq to the wheels on 91 octane:

This Skyline does have basic performance upgrades including: Apex’i intakes, boost restrictor removed (~14psi), Fujitsubo equal-length downpipe, HKS high-flow cat, Fujitsubo Legalis R-Type Evo exhaust, divided intake pipe, PRP R35 coil conversion kit. Despite the modifications, a subtle chop at idle and the dyno results may indicate aftermarket cams from Japan. Nevertheless it has great power, enjoy the dyno video!

 

Enjoying The Ride

We are happy to report that Pall is already back on the road in his R32, post ZCG-tuning. Just yesterday he attended the final Morning Motors in Santa Cruz:

 

Pall attended the 2021 Skyline Matsuri hosted by the Norcal Skyline Owners group, you can see Pall’s own photography from the event by clicking on the photos below:

 Can’t get enough of this beautiful Skyline. It doesn’t get any better than driving a Skyline on Skyline!

 

Pall is a wonderful client and enthusiast with a pretty serious E30 M3 in addition to the R32. The 90’s were good for iconic sports cars!

 

Thanks to Norcal Skyline Owners group we get to work with many cool cars like Kurt W and Mike R (here for timing belt, tuning and clutch job, report soon). Thanks for your support Pall and for trusting us with your R32!

More pictures in the gallery below:

 

The 2021 Japanese Classic Car Show was held on October 30, in Anaheim, CA. This is the original vintage Japanese-car event in SoCal and in its 16th year, JCCS has grown incredibly. Thousands of spectators enjoyed 400+ cars in the parking lot of Angel Stadium. The vehicles themselves remained a fantastic blend of stock, modified and restored. This is the most important show for Japanese cars, and the Z Car Garage crew keeps coming back every year to soak up the sun, see old friends and drool over some spectacular vintage builds.

 

Z Car Garage Parts on Sung Kang’s Datsun 240Zs!

FuguZ

Actor and star of the Fast and the Furious movies, Sung Kang also happens to be a car enthusiast as well. At the SEMA 2015 show he debuted his vision of the perfect Datsun 240Z, named FuguZ. The build was chronicled the through social media, enlisting parts from around the world with final assembly by Kenji at Greddy. Sporting the latest Rocket Bunny body kit, Volk TE37s and NA RB26 drivetrain this was a crowd favorite and sparked the Z car love in many people.

 

FuguZ became one of the most prominent S30s in the world. Fast forward to 2021 and Sung Kang visited Z Car Garage, driving “Mrs. Butters”, our 1971 Series 1 240z shop demo car. After driving Butters, Sung wanted the exact same Z Car Garage Big-Brakes (for small wheels), Z Car Garage CV Axles and KW suspension on his very own FuguZ!

 

Rob and Kenji came up with a plan and the Z was shipped up to us so we could install ZCG Big-brakes, CV axles and KW suspension before the JCCS. Kenji then revived the Z with twin-turbos that the RB26 is famous for. Now Sung can enjoy the boost, and reign it all in with our brakes and suspension. Full report soon!

 

Doc Z

Sung was so impressed with the Z Car Garage Big-Brakes that he also wanted a set on his latest 240Z build, the “DocZ”. We happily obliged, only this time we shipped the kit to the Erick of Erick’s Racing, the master builder behind DocZ.

  

Erick was very pleased with the kit and ease of installation:

 

DocZ was built as a tribute to the Datsun 240Z that dominated the 1971 East-African Safari. Sung even had  his own multi-piece wheels made as an homage to that history-making Z. The ZCG Big-Brakes can be seen through those iconic slots:

 

DocZ also features interior parts (look at that dash!) and exterior carbon fiber pieces by Carbon Signal:

 

We are thrilled to be a part of Sung’s builds and the collaborate with his team of talented craftsman! Thank you for your support Sung! Stay tuned for a deep dive on DocZ when we see it at SEMA this week and more details on the FuguZ when it returns to ZCG for tuning.

Showtime!

 

We arrived early to the new venue at Angel Stadium of Anaheim.  This location is larger and more vendor-friendly than The Queen Mary and Marina Green of past shows. It was a a huge parking lot, and those that braved the lines to get in were treated to a J-Tin overload. Once inside we made our way to see client James and his 1972 Datsun 240Z.

 

James’s 1972 S30 was displayed in the Love20bee booth. At the heart of this beast is a turbocharged L-series managed by Haltech. Chassis upgrades include custom full-length subframe connectors, CD009a 6-speed transmission, KW Suspension, ZCG CV Axles and Big-Brake Kit (328mm) behind RS-8 wheels restored by Love20bee. Larry Chen featured  James’s Z on this episode of Hoonigan Autofocus. Inside, a stack instrument cluster was integrated into the gauge pod, viewed from leather Recaro Pole Position seats:

  

Recent upgrades to “Medusa” include a new tubular exhaust manifold, intake manifold and down-pipe from from ProtunerZ. We will have more installation photos and dyno results coming soon to zcarblog.com!

 

Highlights from JCCS

Enjoy this video I made highlighting the sights and sounds of JCCS 2021:

 

Why do we keep coming back to JCCS? Each year the bar is raised for the show cars, and this year was truly impressive. With over 400 cars and aisles of vendors it was almost impossible to see it all in the 9am-3pm show time. Here are our favorites, starting with Nissan/Datsun.

 

Skylines

Here are few of my favorite Nissans and Datsuns, starting with that not-so forbidden fruit commonly known as the hakosuka Skyline. Ralph Kenyon’s stunning build was the result of OCD-level attention to detail.

  

Ralph’s Hako received a true, rotisserie-style nut and bolt restoration but didn’t stop there. He strengthened the chassis, utilizing beefed-up suspension/driveline components to support the raging and exotic 3.5L Datsunworks twin-cam L-Series. This fuel-injected monster is backed by a Nissan CD009 6speed transmission. Take a look at that engine bay…you will find yourself discovering a treasure of details from the dry-sump tank to perfectly aligned wingnut bolts on the air filter housing. The S20-inspired valve cover, equal-length exhaust manifold, OEM hose clamps…”next level” is appropriately used here.

  

Roy’s ’72 Skyline now with an old-school Cartech turbo kit:

 

Rick’s GTX on RS8 wheels:

 

Mike C’s 4-door:

 

Jun’s unflared Hako:

  

It was great to see our ZCG CV Axles under this 3.2L, fuel-injected Hako in the Hagerty booth!

 

 

I didn’t expect to see a large gathering of R32/33 Skylines, even a 4-door! DR30 and 240k!

  

JDM Legends had their C110 Kenmeri Skyline on display. Now with a 3.5L Jenvey fuel-injected L-Series and 6-speed transmission. It was great to see Eric he expressed how fun it is to drive!

 

Our friend Sean and his team at Toprank International Vehicle Importers brought the heat to JCCS with an impressive showing of rare Skylines. It goes without saying, if you are in the market for a vintage Skyline (or any JDM car) IVI is the place to go. The iconic “BF Goodrich poster” R34 and R33 Nismo 400R were a treat to see in person:

Z Car Extravaganza

 

 

S30 Z cars were everywhere.  I’m a big fan of subtle modified Z’s but I can also appreciate pristine, bone-stock examples and the occasional shakotan build.

Stock is good. Nissan returned to JCCS with a cool display including this pristine example:

 

What a pleasure it was seeing the 2023 Z again since it was at our shop 10/23 for the public to view:

 

 

Jay from JDM Car Parts always has a fun display with RHD/JDM cars surrounded by a working model train (See video):

 

There were an impressive amount of Z’s with bodykits from Rocketbunny and Libertywalk:

 Lowered on Hayashi Racing wheels:

  

Loved this Z on Watanabe wheels with an L28ET:

 

Beautiful 260Z and 280Zs and a 2+2!

  

Andrew’s RHD Fairlady Z sitting on Watanabe “Gotti” wheels was near the Techno Toy Tuning booth. He drove it down with his Father from the Bay Area:

 

So. Many. Z’s!

 

 

The show-winning Z!  Mark and his daughter Samantha built this Z as a family project it is SEMA-bound!

  

Larry Chen’s 1970 SR20DET-powered Z was on display in the Leen Customs booth. It was featured on Hoonigan Autofocus and we will take a closer look at the work ZCG performed this past year including our Z Car Garage Big-Brakes, Z Car Garage CV Axles on zcarblog.com:

    

You can find more S30s in our gallery!

S130!

 

Keeping Z31s on the map was the best display of the model I’ve ever seen at JCCS. Proudly shown right next to the Nissan display there were Kouki, Chuki and Zenki models to enjoy:

     300ZR and Shiro Special sitting on white Watanabe R-type wheels:

 

The lone Infiniti sitting on Autotradas:

 

The Nissan 300ZX (Z32) was also well-represented. My favorite was a white slicktop on Nismo wheels:

Sweet 240sx/Silvias and B13 Sentras!

 

People

At the JCCS  it is always great to see old friends and meet new enthusiasts! The best part was to meet younger folks that were passionate about their rides…we need the the next generation to carry the torch for us!

      

Datsun Fairlady Roadsters

The Datsun Roadsters came out in full force this year, running 12 cars strong!

 

Thanh Lam’s 1964 Datsun 1500 was the oldest car present, winning the JCCS Best of Show award!

  

Ed’s sharp 1970 SPL sporting Enkei Compe wheels:

  

Eric’s show-winning ’68 2000:

  

The Desirello’s also displayed their SR20-powered beauties:

  

More roadster pics in our gallery!

Datsun 510s

 

 

Datsun 510s dominated the field as the most represented model again this year.

 

Not one but 4 Bluebird Coupes!

 

Matt of Love20bee’s Rotary-powered, box-flared 510 sitting on Tomcat wheels. Hear it run in the video above…BRAP!

 

 

Erick’s S2000-powered 510!

 

TSR-built 510s:

  

All kinds of engine swaps abound including Toyota 18RG, SR20, Mazda Rotary and even an LSx V8!

  

This 500hp, SR20-powered 510 was tune by our friend Seb at SpecialtyZ. It’s running our ZCG CV Axles and the owner is super stoked with their performance!

 

Our friend Troy’s customer won Best 510! We saw the happy new owner of Troy’s former race car!

 

Stock RHD 4-door!

Wagons!

Jun Imai’s “Kaidohouse” 510 in the GReddy booth with Work Equip 40 wheels, IRS and KA24DE-T powerplant:

 

Alex’s V8-powered wagon. He also brought a Sunny truck!

     

Toyota

Toyota always has a huge showing with AE86, Cressida, Celica’s and Corolla’s!

   

Great showing of RA29 (Liftback) Celicas!

 

3nd and 4th gen Celicas and Supras!

 

Wheels For Fantasy

I personally love going to JCCS because I get to see very rare Japanese/tuner wheels and parts. Preservation of authentic wheels and appreciation of the time and effort spent to find certain specimens that most folks have never heard of in this generation is what I admire most.

 

Variations on the mesh wheel from BBS, Epsilon, SSR, Volk, Bahn and more. Riverside, Autostrada, Racing Hart, Hoshino, Work, Mugen and Tomcat and Watanabe. Heaven!

  

Honda

EF, EA, EG Civics, CRX, DA and DC Integras, NSX and even motorcycles!

 

 

Super Sexy NSXs

 

Mazda

FC, FD RX-7s were out as well as RX-2, RX-3, REPU pickups and Miatas:

 

Many more pictures from JCCS in the gallery!

 

Farewell

 

Towards the end of the show we staged a quick photoshoot with Sung Kang and the DocZ next to James’ Medusa. It was crazy to see everyone swarm around me once they realized what was going on 🙂

 

Later, at the Greddy booth Kenji and Larry Chen indulged us for another quick photoshoot with James’s Z, FuguZ and Ole Orange Bang. You can see Rob driving FuguZ in the vide0. We are beyond happy to have our Z Car Garage chassis parts on these high-profile Z cars.

 

 

 

Thank You JCCS!

How does a show go by so fast? Just like that, the JCCS ended and we still did not explore the entire show or meet everyone. I personally think there needs to be signage or at least a map so spectators can make sure they see everything! Despite missing out on some displays there was such a great, positive energy. Love seeing families and younger generations of car enthusiasts, for all marques.

It is difficult to run a car show and keep up the quality and interest levels but the folks at JCCS have managed to do exactly that for 16 years! No other show gives you the chance to see obscure, pristine, modified Japanese classics…and we look forward to next year’s entrants. Koji and Terry, thank you for your efforts. We hope you have enjoyed our coverage and please visit our mega-gallery for more pictures.

 
…[read more]